Close
Do you have any questions? Contact us!
I agree to the Terms of Service
UNIQPRO APPLIANCE

Maytag Washing Machine Repair Austin | Reliable Local Service

Fast, same-day Maytag washer repair in Austin and surrounding areas. We specialize in fixing common Maytag issues like loud bearing noises, lid lock failures, and "SD" or "oL" error codes. Our expert technicians use only genuine OEM parts to ensure your heavy-duty appliance lasts. Enjoy honest pricing, no upselling, and a solid 5-month warranty on all Maytag repairs.
🛡️ 5-Month Warranty
🤝 Honest Pricing
Certified Technicians
📍 Local Austin Experts
🛠️ $0 Service Call with Repair

MAYTAG TOP-LOAD WASHER: FIXING LOUD BANGING & BALANCE ISSUES

MAYTAG WASHER REPAIR: FIXING DRAIN FAILURES & CONTROL BOARD ISSUES

A customer in Austin reported their Maytag Front-Load washer was failing to drain at the end of the cycle, leaving clothes soaking wet. The unit was displaying a "Long Drain" error code. Our diagnostic revealed that while the drain pump was not clogged, it wasn't receiving enough voltage to operate at full capacity. The root cause was a failing relay on the Main Control Board (PCB) that was providing insufficient power to the pump motor.
The Solution To restore full drainage and performance to this Maytag unit:
  1. Diagnostic: Performed a voltage drop test at the pump terminal. Confirmed the control board was only sending partial power, which is a common failure point in high-mileage Maytag models.
  2. Board Replacement: Installed a new original Maytag OEM Control Board. We only use factory-certified boards to ensure the internal "Sud" sensors and motor phases are correctly managed.
  3. Pump Optimization: Even though the board was the primary issue, we cleared the internal "coin trap" and pump housing of any minor debris to ensure maximum efficiency for the new system.
  4. Final Cycle Test: Ran a high-speed spin and drain test. Verified the new board provides consistent voltage, allowing the pump to clear all water within the factory-mandated timeframe.
The Result The washer now drains rapidly and silently. The error codes are gone, and the machine is fully operational. This professional repair is backed by our 5-month warranty.
A customer in Austin reported their Maytag Centennial washer was making a violent banging noise during the spin cycle, often "walking" across the laundry room floor. The unit would repeatedly stop and display an "uL" (Unbalanced Load) error, even with only a few items inside. Our diagnostic confirmed that the suspension rods had lost their dampening tension, causing the tub to bounce uncontrollably.
The Solution To stabilize the machine and protect the outer tub:
  1. Diagnostic: Performed a "bounce test" on the tub. Confirmed that the springs were stretched and no longer absorbing the energy of the high-speed spin.
  2. Part Replacement: Installed a full set (4) of brand-new original Maytag OEM suspension rods. We always replace the entire set to ensure even weight distribution and prevent premature failure of a single rod.
  3. Leveling: Checked the machine’s leveling legs and reinforced the floor contact points to minimize vibration.
  4. Calibration: Ran a heavy-load test cycle to verify the tub remains centered and the machine operates quietly at maximum RPM.
The Result The "walking" and banging are gone. The washer is once again whisper-quiet and completes the spin cycle efficiently. This essential mechanical repair is backed by our 5-month warranty.

Professional Appliance Repair Across Greater Austin

We provide fast, same-day repair services for all major washing machine brands throughout the Austin metropolitan area and surrounding cities. Our technicians are always nearby, ensuring your appliances are back in service without delay.
  • Austin (All Neighborhoods)
  • Round Rock
  • Cedar Park
  • Pflugerville
  • Georgetown
  • Leander
  • Lakeway
  • Bee Cave
  • Hutto
  • Buda & Kyle
  • Manor
  • West Lake Hills

Heating element went out in our dryer. Uniqpro technician Dimitri was wonderful. He also found that white thing in the middle was very worn. He gave the entire dryer a checkup! He replaced the white thing at cost of the part. Very clean, affordable, professional. Fast response with accurate quote.

We will be calling Dimitri again.

I’ve got respond in 10 min after I post my order and the tech was in my house next day. He gave me very detailed evaluation what should be repair for very reasonable price, without upselling! He fixed ice maker in my Samsung fridge, replaced a water filter and in addition for the same price cleaned vacuumed condenser coil, fan, etc.

GREAT 5 STAR SERVICE! Thank you.

  • Nick M.

Dmitri helped us with very short notice. He efficiently and expertly repaired our Asko washing machine. I was expecting to wait weeks to get in with a certified Asko repair person however he was very familiar with Asko and better than anyone we have. He is smart, knowledgeable and very kind.His price was extremely fair, almost too little for what the work he did.

Highly recommend!

I plan on using Dimitri whenever I need an appliance repair moving forward. He's an experienced and very sweet young man who is starting his own repair business and he responded quickly to my Yelp inquiry. He was at my home within 2 hours to replace the faulty oven ignition in my 5 year old Samsung range. He was in and out in just an hour, and again he was very kind and his pricing was very reasonable. Thanks Dimitri!

Real Feedback from Real Customers
info@uniqproappliance.com
Business address: 9417 Great Hills, Austin,TX, 78759
+1 (737) 500-1555
Uniqpro Appliance Repair Llc © 2026
Made on
Tilda