Close
Do you have any questions? Contact us!
I agree to the Terms of Service
BACK

Kenmore Washing Machine Repair Austin | Reliable Local Service

Fast, same-day Kenmore washer repair in Austin and surrounding areas. We specialize in fixing common Kenmore issues like UE errors, lid lock failures, and drainage problems. Our expert technicians use only genuine OEM parts to ensure your appliance lasts. Enjoy honest pricing, no upselling, and a solid 5-month warranty on all Kenmore repairs.
🕒 Get a Quote in 10 Mins
Book online 📅
🛡️ 5-Month Warranty
🤝 Honest Pricing
✅ Certified Technicians
📍 Local Austin Experts
🛠️ $0 Service Call with Repair

KENMORE Washer Repair: Fixing Drain & Pump Issues

KENMORE WASHER REPAIR: FIXING UNBALANCED LOAD & UE ERRORS

The root cause was a set of worn-out Suspension Support Rods. The internal springs had lost their tension over time, causing the tub to bounce unevenly. This triggered constant UE (Unbalanced Error) alerts, preventing the machine from reaching high-speed spin and leaving clothes soaking wet.
The Solution To ensure long-term reliability, we performed the following steps:
  1. Genuine Parts: We installed four heavy-duty Kenmore OEM suspension rods. These are specifically designed to stabilize the tub during heavy loads of towels or bedding.
  2. Professional Installation: Removed the top cover and replaced each rod individually to ensure the tub remains perfectly centered within the cabinet.
  3. Calibration: Conducted a high-speed spin test to verify that the tub no longer hits the side panels and remains steady throughout the cycle.
The Result The washer is now whisper-quiet and stays firmly in place even at maximum RPM. Another successful repair in Austin that saved the customer the cost of a brand-new appliance.

KENMORE TOP-LOAD WASHER: FIXING LID LOCK & SPIN CYCLE FAILURES

A customer in Austin reported their Kenmore Top-Load washer was filling with water but refused to start the wash cycle or spin. The "Lid Lock" light was either flashing or not coming on at all, and the drum remained completely still. Our diagnostic showed that the control board wasn't receiving the safety signal from the lid switch, preventing the motor from engaging for the spin and wash phases.
The Solution To get the drum spinning again and ensure safe operation:
  1. Diagnostic: Ran a manual component test to verify if the strike was hitting the latch correctly. Confirmed the internal solenoid of the Lid Lock Assembly had failed electrically.
  2. Part Replacement: Installed a new original Kenmore OEM Lid Lock. Using factory-certified latches is crucial for Kenmore units to ensure the lid stays securely locked during high-speed spins.
  3. Strike Alignment: Inspected the lid strike (the plastic hook) for any wear or misalignment that could cause the new lock to fail prematurely.
  4. Calibration: Performed a full recalibration of the washer’s control system to clear the previous error codes and sync the new hardware.
The Result The washer now locks securely, and the drum spins at full speed without hesitation. The cycle completes from start to finish perfectly. This essential safety repair is backed by our 5-month warranty.

KENMORE WASHER REPAIR: FIXING POWER ISSUES & CONTROL BOARD FAILURE

A customer in Austin reached out because their Kenmore Elite washer suddenly stopped powering on. The control panel was completely dark, and the unit wouldn't respond to any start commands. After testing the power cord and the line filter, our diagnostics confirmed a failure in the Main Electronic Control Board (PCB). A relay on the board had failed, preventing electricity from reaching the display and motor.
The Solution To restore power and save the appliance, we performed the following:
  1. Diagnostic: Verified voltage at the board's input and confirmed no output was being sent to the user interface.
  2. OEM Replacement: Installed a brand-new original Kenmore OEM control board. Using factory-certified parts is essential for Kenmore washers to maintain correct cycle timing and sensor accuracy.
  3. Harness Check: Inspected the wiring harness for any loose connections or signs of overheating that could have triggered the board failure.
  4. System Test: Ran a "Quick Test" cycle to ensure the new board correctly communicated with the motor, lid lock, and water valves.
The Result The washer powers on instantly and functions like new. The customer avoided the high cost of a replacement machine. This professional repair is backed by our 5-month warranty.

KENMORE TOP-LOAD WASHER: FIXING CONSTANT PUMP NOISE & CYCLE FAILURES

Our customer in Austin reported their Kenmore Top-Load washer was stuck in a "constant running" mode. The machine would make a constant humming or motor-like sound, which we quickly identified as the drain pump running continuously. The unit refused to advance to the wash cycle or fill with water. Even when turned off and back on, the annoying sound persisted, and the control panel was completely unresponsive to new commands.
The Solution To restore full cycle control to this Kenmore washer:
  1. Diagnostic: Ran a diagnostic test to verify that the drain pump was receive constant voltage and was not physically obstructed.
  2. OEM Replacement: Replaced the failed Main Electronic Control Board with a brand-new original Kenmore OEM board. This is the core component that regulates all pump and motor functions.
  3. Harness Inspection: Carefully inspected the wire harness for any signs of heat or moisture that could have caused the original board to fail.
  4. Calibration: Performed a factory recalibration to sync the new board with the water level sensor and lid lock assembly.
The Result The constant noise is gone, and the washer now powers on and completes all stages of its cycles perfectly. The customer saved the expense of buying a new washer with this precise electronic repair. This premium repair is backed by our 5-month warranty.

KENMORE WASHER REPAIR: FIXING WATER INLET VALVE LEAKS & SLOW FILL ISSUES

A customer in Austin reported their Kenmore washer was slowly filling with water while turned off, causing a puddle in the drum. Additionally, during regular use, the machine would take an unusually long time to fill, often triggering an error code and stopping the cycle. Our diagnostic confirmed the water inlet valve had a mechanical failure, preventing it from sealing properly and restricting water flow.
The Solution To prevent potential flooding and restore the machine's efficiency:
  1. Diagnostic: Verified the solenoid resistance and confirmed the internal diaphragm was leaking.
  2. Part Replacement: Installed a new original Kenmore OEM Water Inlet Valve. Using genuine parts ensures the water pressure sensors work accurately with the control board.
  3. System Maintenance: Inspected and cleaned the fill hoses and filter screens to remove sediment from the local Austin water supply.
  4. Testing: Ran a test cycle to ensure the water shuts off instantly and the "fill time" is back to factory specifications.
The Result The drum stays dry when the washer is off, and cycles now run without delays. The unit is back to peak performance. This repair is backed by our 5-month warranty.
When an Kenmore front-load washer fails to drain, it often triggers the OE error code. After a thorough inspection of the drain system and checking for debris in the filter, we tested the pump for mechanical failure. Our diagnostic confirmed that the drain pump motor had seized, preventing the washer from emptying the water and advancing to the spin cycle.
The Solution
  1. Pump Replacement: We replaced the defective part with a new genuine KENMORE OEM drain pump to ensure factory-standard performance.
  2. System Flush: We cleared the internal drain lines and debris filter to prevent future clogs and ensure optimal water flow.
  3. Calibration & Test: Ran a specialized test mode to verify that the drainage is now instantaneous and the motor operates quietly.
The Result
The washer now drains perfectly, and the spin cycle is back to normal. The customer is happy to have their KENMORE machine running like new again.

Professional Appliance Repair Across Greater Austin

We provide fast, same-day repair services for all major washing machine brands throughout the Austin metropolitan area and surrounding cities. Our technicians are always nearby, ensuring your appliances are back in service without delay.
  • Austin (All Neighborhoods)
  • Round Rock
  • Cedar Park
  • Pflugerville
  • Georgetown
  • Leander
  • Lakeway
  • Bee Cave
  • Hutto
  • Buda & Kyle
  • Manor
  • West Lake Hills

Heating element went out in our dryer. Uniqpro technician Dimitri was wonderful. He also found that white thing in the middle was very worn. He gave the entire dryer a checkup! He replaced the white thing at cost of the part. Very clean, affordable, professional. Fast response with accurate quote.

We will be calling Dimitri again.

I’ve got respond in 10 min after I post my order and the tech was in my house next day. He gave me very detailed evaluation what should be repair for very reasonable price, without upselling! He fixed ice maker in my Samsung fridge, replaced a water filter and in addition for the same price cleaned vacuumed condenser coil, fan, etc.

GREAT 5 STAR SERVICE! Thank you.

  • Nick M.

Dmitri helped us with very short notice. He efficiently and expertly repaired our Asko washing machine. I was expecting to wait weeks to get in with a certified Asko repair person however he was very familiar with Asko and better than anyone we have. He is smart, knowledgeable and very kind.His price was extremely fair, almost too little for what the work he did.

Highly recommend!

I plan on using Dimitri whenever I need an appliance repair moving forward. He's an experienced and very sweet young man who is starting his own repair business and he responded quickly to my Yelp inquiry. He was at my home within 2 hours to replace the faulty oven ignition in my 5 year old Samsung range. He was in and out in just an hour, and again he was very kind and his pricing was very reasonable. Thanks Dimitri!

Real Feedback from Real Customers
info@uniqproappliance.com
Business address: 9417 Great Hills, Austin,TX, 78759
+1 (737) 500-1555
Uniqpro Appliance Repair Llc © 2026
Made on
Tilda